Track repair and alignment · Tucson, AZ
Discount Door Service repairs and realigns garage door tracks across Tucson, AZ, Oro Valley, Marana, Vail, Sahuarita, Rita Ranch and the Catalina Foothills. Bent, spread or misaligned track is what people see, but it is almost always the second event. A roller disintegrates, a cable jumps its drum, a lag bolt works loose, or something clips the track with a vehicle, and the door leaves the rail as a consequence. We straighten or replace the track, re-square the assembly, and fix whatever put the door there in the first place. Woman owned since 1999, licensed ROC #322606. Call (520) 579-9084.
Cause, not just symptomWe find what put the door off track before realigning it
Do not run itEvery cycle on a bad track bends more of it
ROC #322606Licensed, bonded and insured
27+ yearsServing Tucson since 1999
Door off track? Call (520) 579-9084 · Stay out from under a hanging door · Same-day where we can
Is this your door?
Track faults announce themselves early. Catching one at the noise stage is a different job to catching it after the door has come off.
01
The rail has spread. Once the roller is not captured properly it is a matter of time before the door jumps out under load.
02
A dent or a kink in the rail. The door forces through it, and every pass makes the flat spot on the roller worse.
03
Usually impact, or a lag bolt that has worked out of the framing. Either way the geometry has changed and the door is no longer running square.
04
Stop. Do not operate it, do not try to lever it back on, and do not stand under it. It is being held by whatever the cables have left.
A roller that shed its bearing, a cable off its drum, a loose fixing or an impact. Realigning without finding this simply schedules the next call-out.
Minor dents can be dressed out. Track that is kinked, spread or creased gets replaced, because straightened steel rarely holds its shape under load.
Both vertical rails plumb, horizontals level and parallel, and the flare set correctly, so the rollers are captured through the full travel.
Rollers that came off a track are usually flat-spotted, and the cables often need re-seating on their drums.
Get a free quote
Tell us what the door is doing. If it is off the track, call rather than send the form.
Talk to us now
Melissa, ownerFamily run in Tucson. The person who quotes your job is the person who stands behind it.
What to expect
A door off its track is made safe before it is diagnosed.
01
Clamped or supported so it cannot move while we work out what happened.
02
You are shown the actual fault, and given the number before any work starts.
03
Track squared, parts replaced, and the door cycled several times under power to prove it runs clean.
What changes the price
Realigning a rail and rebuilding a door that has come off are very different pieces of work. Four things decide which one you have.
Adjusting a rail that is sound costs a fraction of replacing a section that is kinked.
The curved section is the most awkward and the most commonly damaged, because that is where the load changes direction.
Rollers, hinges, cables and sometimes a bottom bracket, depending on how the door left the rail.
The one you control. A door operated after it jumped the track does most of its damage in those few cycles.
You get the price before work starts, and we will tell you plainly when a rail can be saved rather than replaced.
Tucson homeowners
The most common sequence we see is a roller failing, the door starting to bind, the opener forcing it through, and the rail spreading until the door jumps out. That is why a noisy door is worth a phone call: at the noise stage it is a roller, and at the off-track stage it is a rail, several rollers and half a day.
27+
Years serving Tucson
1,500+
Homes served
ROC #322606
Licensed, bonded, insured
Same day
Most repairs in one visit
Straight answers
We would strongly advise not. The door is under spring tension and is being held by cables that may already be compromised. This is the repair that most often produces injuries when it is attempted at home.
It depends where and how badly. Shallow dents in a straight run can often be dressed out. Creased or spread rail, and almost any damage to the curved section, gets replaced.
In order of how often we see it: a failed roller, a cable off its drum, a loose fixing, and impact from a vehicle. It is very rarely the track deciding to fail on its own.
Yes. It is a heavy panel held by whatever is left of the cables and it can come down without warning. Keep people and cars out from under it.
No, and this is a common mistake. The rollers get lubricated, the track gets cleaned. Grease in the rail collects Tucson dust and makes the problem worse.
Track repair and alignment across Tucson and Southern Arizona. Licensed ROC #322606.
